A750F AUTOMATIC TRANSMISSION / TRANSAXLE: SHIFT LEVER: INSPECTION (2008 Sequoia)

Last Modified: 11-29-2007		1.6 G
Service Category: Drivetrain	Section: Automatic Transmission/Transaxle
Model Year: 2008	Model: Sequoia	Doc ID: RM0000030G600LX
Title: A750F AUTOMATIC TRANSMISSION / TRANSAXLE: SHIFT LEVER: INSPECTION (2008 Sequoia)

INSPECTION

1. INSPECT SHIFT LOCK CONTROL ECU

(a) Measure the voltage according to the values in the table below.

HINT:

Do not disconnect the shift lock control ECU connector.

Standard Voltage:

If the result is not as specified, replace the shift lock control ECU.

(b) Measure the resistance according to the value(s) in the table below.

HINT:

Do not disconnect the shift lock control ECU connector.

Standard Resistance:

Tester Connection	Condition	Specified Condition
8 (E) - Body ground	When battery voltage not applied	Below 1 Ω

If the result is not as specified, replace the shift lock control ECU.

(d) Measure the voltage according to the values in the table below.

HINT:

Do not disconnect the shift lock control ECU connector.

Standard Voltage:

Tester Connection	Switch Condition	Specified Condition
1 (SLS+) - 2 (SLS-)	Ignition switch off	Below 1 V
1 (SLS+) - 2 (SLS-)	Ignition switch ON	Below 1 V
1 (SLS+) - 2 (SLS-)	Ignition switch ON and brake pedal depressed	11 to 14 V

If the result is not as specified, replace the shift lock control ECU.

2. INSPECT SHIFT LOCK SOLENOID

(a) Disconnect the shift lock solenoid connector from the shift lock control ECU.

(b) Measure the resistance according to the values in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
1 (SLS+) - 2 (SLS-)	When battery voltage not applied	101 to 123 Ω
3 (E2) - 4 (P)	Shift position P	10 kΩ or higher
3 (E2) - 4 (P)	Shift position not P	Below 1 Ω

If the result is not as specified, replace the transmission floor shift assembly.

(c) Apply 12 V battery voltage to the shift lock solenoid valve and check that the valve moves and makes an operating noise.

OK:

Measurement Condition	Specified Condition
Battery positive (+) → Terminal 1 (SLS+) Battery negative (-) → Terminal 2 (SLS-)	Solenoid moves and makes an operating noise

Measurement Condition

Specified Condition

Battery positive (+) → Terminal 1 (SLS+)

Battery negative (-) → Terminal 2 (SLS-)

Solenoid moves and makes an operating noise

If the result is not as specified, replace the transmission floor shift assembly.

3. INSPECT TRANSMISSION CONTROL SWITCH

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
3 (IG) - 7 (S)	Shift position S	Below 1 Ω
3 (IG) - 7 (S)	Shift position not S	10 kΩ or higher
2 (SFTU) - 5 (E)	Shift lever continuously shifted to "+" position (Up-shift)	Below 1 Ω
2 (SFTU) - 5 (E)	Shift position S	10 kΩ or higher
1 (SFTD) - 5 (E)	Shift lever continuously shifted to "-" position (Down-shift)	Below 1 Ω
1 (SFTD) - 5 (E)	Shift position S	10 kΩ or higher

If the result is not as specified, replace the transmission floor shift assembly.